EMT Practice Test

1. Question Content...

---

Question1: A technician needs to add a server as a host to an existing VMware environment. The server has 2x 1Gb LOM ethernet ports and a 4-port 1Gb Broadcom NIC. The 2 LOM ports are teamed to be used as SAN connections. All active data and management traffic should utilize the 4x 1Gb ports on the Broadcom NIC. The technician needs to achieve management and data redundancy at the hardware level to handle a single port failure.
What is the most effective way to meet this requirement?

Question2: How can a system administrator compare the currently installed hardware to the original system configuration?

Question3: A server arrives without any RAID configuration. All firmware is up to date. The server has a PERC H730p controller. The technician needs to configure the required RAID arrays prior to OS installation.
Which three methods can be used to configure the RAID arrays? (Choose three.)

Question4: A server needs to be configured with a six disk RAID 10 using 3 TB drives.
What should be the available array size in this configuration?

Question5: A technician needsto set a server to always attempt PXE boot beforebooting to the harddrive.
What two itemsdoes thetechnicianneed to set to achieve this? (Choose two.)

Question6: A technician is sent on-site to troubleshoot a server that reports errors during POST when rebooted. The LCD is amber. The error message is as shown:
correctable memory error rate exceeded for DIMM B4
The server has a limited maintenance window. The technician needs to troubleshoot efficiently.
Which step should the technician take to troubleshoot?

Question7: A technician wants to move memory from a few older system into a newer system.
What is the most efficient method for the technician to accomplish this task?

Question8: A systemboard was replaced. After the replacement, the system will NOT boot into Windows and gives the error 'No boot device found'. Virtual disks are seen and optimal.
What action should a technician take to resolve this issue?

Question9: A technician needs to troubleshoot a server. The OS was operational. After an untrained person accesses the System Setup utility on the server, the OS now fails to load.
The technician reboots the server, selects F2, accesses the System Setup utility, and selects System BIOS.
The technician needs to verify items in the System BIOS settings before reloading the OS.
Which two items should the technician verify? (Choose two.)

Question10: Refer to the exhibit.

A technician it installing an OS to a server. The OS array is 2.8TBs. The OS install is unable to start.
What should the technician do to install the OS?

Question11: A technician is updating firmware on a Windows Server using the Lifecycle Controller following a NIC replacement, but it fails to complete the update on the NIC despite successfully updating other components.
The update's readme confirms that the current version is too old to upgrade with the Lifecycle Controller and an alternative method must be used.
Which three update methods could the technician use to meet this requirement? (Choose three.)

Question12: A server has two 1100w power supplies. The system needs to enable or disable power supplies dynamically depending on power needs. Power Supply 2 needs to be main power supply.
Which two settings should the technician change? (Choose two.)

Question13: A technician has a 13G system that is giving NO video to a crash cart connected to the front VGA port. The LCD is NOT reporting any errors. The system reports 'CPU Resetting' messages sporadically in the lifecycle log. The iDRAC runs an Express license.
The technician needs to most efficiently determine if the system is completing POST despite the video issue.
Which two steps should the technician take to perform this task? (Choose two.)

Question14: A technician needs to configure a server to allow the OS to manipulate processor frequencies for higher power efficiency.
How should the technician perform this task?

Question15: A technician needs to initially configure a server from a bare metal condition in the following areas:
* Processor settings
* Disk configuration
* iDRAC network settings
The technician can only reboot once to achieve these tasks.
Where should the technician configure these settings? (Choose three.)

Question16: A PowerEdge server is running a hypervisor. The server must be configured to enable multiple virtual machines to share the PCIs hardware resources of a supported NIC.
Which System BIOS setting must be enabled to provide this functionality?

Question17: A technician deploys a server. The iDRAC was configured with a static IP address and hostname.
The technician can NOT ping the iDRAC from the workstation when using the hostname.
The technician can ping the iDRAC with the IP address.
Which setting should the technician configure to fix the deployment?

Question18: A technician needs to configure a server to PXE boot a server setup image with the BIOS in UEFI mode.
Which two steps should the technician perform to enable this function? (Choose two.)

Question19: Refer to the exhibit.

A technician tries to apply a BIOS update through the iDRAC web interface on a server using the Linux Dell Update Package file BIOS_2H4CC_LN_2 0.2.BIN. The error shown occurs.
How should this error be fixed?

Question20: A technician in Portland, Oregon has been asked to update the firmware on a server in Omaha, Nebraska. They will use an NFS server also located in Nebraska for serving patches that have been vetted by their security teams.
What two pieces of information does the technician need in order to access the NFS patch server from the Lifecycle Controller or iDRAC? (Choose two.)

Question21: A technician needs to deploy a server into production. The technician needs to verify that the firmware levels match corporate policy before putting the server on the business network.
Which two methods should the technician use to verify the firmware version of iDRAC and BIOS? (Choose two.)

Question22: Which three steps must a technician take prior to replacing a server component with blue tabs/release? (Choose three.)

Question23: A technician sets up Automatic Updates via the iDRAC GUI to schedule updates for 9pm that day. The next morning, the technician notices that the updates were NOT applied.
What configuration change will allow this process to be automated?

Question24: A server is configured with a RAID 5 Virtual Disk across 5 hard disks and 1 spare disk. If a hard disk failure occurs within the RAID 5 virtual disk, the spare disk needs to be online as quickly as possible. It is acceptable for users to experience decreased performance during the rebuild procedure.
How should this requirement met?

Question25: A technician creates two virtual disks and assigns a dedicated hot spare to each virtual disk. The technician also creates a global hot spare.
A drive fails on the second virtual disk.
What is the result?

Question26: An existing server is transferred to a new location. When the iDRAC port is plugged into the network, it causes an IP conflict.
The technician is directed to change iDRAC settings via the LCD Front Panel Display.
There is NO option to make changes.
What is the most probable cause of this issue?

Question27: A technician has a server in production. The iDRAC SEL log indicates a possible issue with DIMMs A1 and A2. Firmware is up to date.
What is the most efficient way to troubleshoot this issue?

Question28: A technician is tasked to perform a RAID Level Migration (RLM) of a RAID 5 array to a RAID 6 array. The technician backs up data and looks in OpenManage Server Administrator to find that the current RAID 5 array is sliced into two virtual disks.
What should the technician do to achieve the desired RAID level?